Acura Wheel Lug Nut Torque Chart, Acura, Specs, Wheel Torque, Wiki, Sparky Express.

Acura Lug Nut Torque Specs

Acura Lug Nut Torque Chart, All Models.

If you are planning on installing a wheel on your Acura, it is important to be aware of the manufacturer's recommended lug nut torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Acura Lug Nut Torque Specs table provided on this page was compiled for quick reference when you are not sure what torque specs should be used to tighten the lug nuts on your Acura vehicle. Our table with Acura lug nut torque specs is a handy tool for many DIY enthusiasts and roadside assistance providers who are unable to locate the vehicle manual when they are helping drivers.

Using the manufacturer's recommended lug nut torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your Acura vehicle’s recommended torque.

Acura Lug Nut Torque Specs, Recommendations

Make Model Submodel Year Nut Torque

ACURA

CL 2.2L COUPE 1997 80 ft-lbs
CL 2.3L COUPE 1998-1999 80 ft-lbs
TL 2.5L SEDAN 1996 - 1998 80 ft-lbs
CL 3.0L COUPE 1997 - 2000 80 ft-lbs
CL 3.2L COUPE 2001 - 2003 80 ft-lbs
TL 3.2L SEDAN 1996 - 2003 80 ft-lbs
3.2TL-S ALL / SEDAN 2001 - 2003 80 ft-lbs
3.5RL ALL / SEDAN 1996 - 2004 80 ft-lbs
ILX 17"BASE / 2.4L 2013 - 2018 80 ft-lbs
ILX ALL 2019 View
ILX ALL 2020 View
INTEGRA CPE/SDN / LS/GS 1986 - 2001 80 ft-lbs
LEGEND LS COUPE / GS SEDAN 1986 - 1995 80 ft-lbs
MDX 4WD- / SUV 2001 - 2006 80 ft-lbs
MDX 18"BASE / ALL 2007 - 2013 95 ft-lbs
MDX 18"BASE / ALL 2014 - 2016 80 ft-lbs
MDX 18"BASE / ALL 2018 - 2018 95 ft-lbs
MDX ALL 2019 View
MDX Sport Hybrid 2019 View
MDX ALL 2020 View
MDX Sport Hybrid 2020 View
NSX COUPE / ALL 1991 - 2005 80 ft-lbs
NSX ALL / COUPE 2016 - 2018 120 ft-lbs
RDX 18"BASE / ALL 2007 - 2018 80 ft-lbs
RDX ALL 2019 View
RDX ALL 2020 View
RDX ALL 2021 View
RL 18"BASE / ALL 2005 - 2012 95 ft-lbs
RLX 19"BASE / BASE 2014 - 2018 95 ft-lbs
RLX Hybrid 2019 View
RLX Hybrid 2020 View
RSX 17-INCH / BASE/TYP S 2002 - 2006 80 ft-lbs
SLX 4 DOOR / SUV 1996 - 1999 90 ft-lbs
TL 17"BASE / BASE SEDAN 2004 - 2008 80 ft-lbs
TL 17"BASE / BASE 2009 - 2014 95 ft-lbs
TLX 17"BASE / 2.4 2016 - 2019 80 ft-lbs
TLX ALL 2019 View
TLX ALL 2020 View
TSX ALL / SEDAN 2004 - 2006 90 ft-lbs
TSX 17"BASE / SPRT WAGON 2007 - 2014 80 ft-lbs
VIGOR CPE/SDN / ALL 1992 - 1994 80 ft-lbs
ZDX 19"BASE / ALL 2010 - 2013 90 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.