Bentley Wheel Lug Nut Torque Chart


Bentley Wheel Lug Nut Torque Chart, All Models.

If you are planning on installing a wheel on your Bentley, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed.The Bentley Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Bentley vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Bentley Wheel Lug Nut Torque Chart, Recommendations

Make Model Trim Year Range Torque

BENTLEY

ARNAGE - ALL FINAL / SEDAN 1999 - 2010 75 ft-lbs
AZURE CONVRT / 255/50R18 1996 - 2006 50 ft-lbs
AZURE 19" BASE / SEDAN 2007 - 2010 100 ft-lbs
BENTAYGA 20"BASE / SUV 2017- 2018 Refer to owner's manual ft-lbs
BENTLEY 8 4 DOOR / SEDAN 1987 - 1992 50 ft-lbs
BROOKLANDS 4 DOOR / R 1993 - 1998 50 ft-lbs
BROOKLANDS 20" BASE / SEDAN 2008 - 2010 100 ft-lbs
CONTINENTAL - ALL 21"BASE / SPEED 2012 - 2017 110 ft-lbs
CONTINENTAL 2 DOOR / 255/55R17 1986 - 2004 50 ft-lbs
CORNICHE 2 DOOR / CONVERTBLE 1985 - 1985 50 ft-lbs
EIGHT SEDAN 1988 - 1992 50 ft-lbs
FLYING SPUR 19"BASE / V8 2014 - 2018 110 ft-lbs
MULSANNE 20"BASE / ALL 2011 - 2018 110 ft-lbs
TURBO R 4 DOOR / RT 1989 - 1997 50 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.