Buick Wheel Lug Nut Torque Chart, Buick, Specs, Wheel Torque, Wiki, Sparky Express.

Buick Lug Nut Torque Specs

Buick Lug Nut Torque Specs, All Models

If you are planning on installing a wheel on your Buick vehicle, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Buick Wheel Lug Nut Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Buick vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Buick Lug Nut Torque Specs, Recommendations

This chart contains Buick Wheel Lug Nut Torque specs for Buick vehicles up to 2018. For 2019 and 2020 Buick wheel bolt torque specs updates, please scroll to the last two rows at the bottom of the table below.

Make Model Trim Year Range Torque

BUICK

CASCADA 20"BASE / CONVERTBLE 2016 - 2018 100 ft-lbs
CENTURY 4 DOOR / CUSTM/LMTD 1986 - 2005 100 ft-lbs
ELECTRA 14-INCH / BASE/ULTRA 1980 - 1990 100 ft-lbs
ENCLAVE 19"BASE / ALL 2008 - 2018 140 ft-lbs
ENCORE 18"BASE / BASE 2013 - 2018 100 ft-lbs
ENVISION 19"BASE / BASE 2016 - 2016 100 ft-lbs
GRAND NATIONAL ALL / COUPE 1984 - 1987 100 ft-lbs
LACROSSE 17"OPT. / CX 2005 - 2009 100 ft-lbs
LACROSSE 17"BASE / 2.4 4-CYL 2010 - 2015 110 ft-lbs
LACROSSE 17"BASE / 2.4 4-CYL 2016 - 2016 125 ft-lbs
LACROSSE 18"BASE / 3.6 6-CYL 2018 - 2018 100 ft-lbs
LESABRE BASE / BESTSELLER 1986 - 2005 100 ft-lbs
LUCERNE 17"BASE / CX 2006 - 2011 100 ft-lbs
PARK AVE SEDAN / BASE/PREST 1991 - 2005 100 ft-lbs
RAINIER 2WD / CXL 2004 - 2007 100 ft-lbs
REATTA 15-INCH / COUPE 1988 - 1991 100 ft-lbs
REGAL ALL / GS 1984 - 2004 100 ft-lbs
REGAL 18"BASE / BASE 2011 - 2018 110 ft-lbs
REGAL T-TYPE ALL / COUPE 1984 - 1987 100 ft-lbs
RENDEZVOUS 4WD / CX+/CXL+ 2001 - 2006 100 ft-lbs
RIVIERA ALL / ALL 1986 - 1999 100 ft-lbs
ROADMASTER SDN/WGN / 225/75R15 1991 - 1996 100 ft-lbs
SKYHAWK 13-INCH / CPE/SDN 1984 - 1989 100 ft-lbs
SKYLARK 15-INCH / CPE/SDN 1986 - 1998 100 ft-lbs
SOMERSET 13"BASE / ALL 1985 - 1987 100 ft-lbs
TERRAZA SPORTVAN / CX/CX+/CXL 2005 - 2007 100 ft-lbs
VERANO 17"BASE / BASE 2012 - 2016 100 ft-lbs
2019 BUICK ALL 2019 BUICK ALL 2019 View table
2020 BUICK ALL 2020 BUICK ALL 2020 View table

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.