Chrysler Wheel Lug Nut Torque Chart


Chrysler Wheel Lug Nut Torque Specs, All Models

If you are planning on installing a wheel on your Chrysler vehicle, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.The Chrysler Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Chrysler vehicle.

Chrysler Wheel Lug Nut Torque Specs, All Models

This chart contains Chrysler Wheel Lug Nut Torque specs for Chrysler vehicles up to 2018. For 2019 and 2020 Chrysler wheel bolt torque specs updates, please scroll to the last two rows at the bottom of the table below.

Make Model Trim Year Range Torque

CHRYSLER

200 - ALL 18"BASE / LIMITED 2011 - 2016 100 ft-lbs
300 - ALL SEDAN / LIMITED 1999 - 2013 110 ft-lbs
300 - ALL SEDAN / LIMITED 2014 - 2020 130 ft-lbs
ASPEN 18-INCH / LMTD 2WD 2007 - 2009 135 ft-lbs
CIRRUS 4 DOOR / LX / LXI 1995 - 2000 100 ft-lbs
CONCORDE 15-INCH / SEDAN 1993 - 2004 100 ft-lbs
CONQUEST ALL / TSI/5-LUG 1985 - 1989 80 ft-lbs
CROSSFIRE ROADSTER / 193-CHASIS 2004 - 2008 80 ft-lbs
CROSSFIRE SRT-6 ALL / 193 CHASIS 2005 - 2006 85 ft-lbs
FIFTH AVE 2/4 DOOR / ALL 1984 - 1989 85 ft-lbs
FIFTH AVE 2/4 DOOR / ALL/FWD 1990 - 1993 95 ft-lbs
GRAND VOYAGER FWD / P205/75R14 1996 - 2001 110 ft-lbs
IMPERIAL 2/4 DOOR / ALL/FWD 1990 - 1993 95 ft-lbs
LASER 14-INCH / ALL/5 LUG 1985 - 1986 95 ft-lbs
LE BARON ALL / ALL/4LUG 1985 - 1995 95 ft-lbs
LHS 16-INCH / SEDAN 1999 - 2001 110 ft-lbs
LHS 4/DOOR / ALL 1994 - 1997 95 ft-lbs
NEON 14-INCH / BASE/LX 2001 - 2001 100 ft-lbs
NEW YORKER 2/4 DOOR / ALL 1986 - 1996 95 ft-lbs
PACIFICA 17"BASE / TOURING-L

2018 - 2020

100 ft-lbs
PACIFICA 17-INCH / ALL 2004 - 2008 85 ft-lbs
PROWLER 2 DOOR / ROADSTER 1999 - 2002 100 ft-lbs
PT CRUISER WAGON / TOURING 2000 - 2010 110 ft-lbs
SEBRING - 16 INCH 16-INCH / LXI COUPE 1995 - 2010 100 ft-lbs
SEBRING - 15 INCH 15-INCH / JX/JXI 1999 - 2007 110 ft-lbs
SEBRING 17-INCH / LXI COUPE 1999 - 2006 80 ft-lbs
SEBRING 15-INCH / JX/JXI 1996 - 1998 95 ft-lbs
T&C VAN ALL / FWD 1990 - 2007 110 ft-lbs
TC ALL / CONVERTBLE 1989 - 1991 95 ft-lbs
TOWN & COUNTRY 17"BASE / LIMITED 2012 - 2016 105 ft-lbs
TOWN & COUNTRY 16"BASE / TOURING 2008 - 2008 115 ft-lbs
TOWN & COUNTRY 16"BASE / LX 2009 - 2011 95 ft-lbs
VOYAGER 5-100 / BASE/ALL 1996 - 2003 110 ft-lbs
2019 Chrysler All Models ALL 2019 View
2020 Chrysler All Models ALL 2020 View

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.