Ferrari Wheel Lug Nut Torque Chart, Ferrari, Specs, Wheel Torque, Wiki, Sparky Express.

Ferrari Lug Nut Torque Specs

Ferrari Lug Nut Torque Specs, All Models

If you are planning on installing a wheel on your Ferrari, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Ferrari Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Ferrari vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Ferrari Wheel Lug Nut Torque Specs Recommendations

Make Model Submodel Year Range Torque
FERRARI 246 DINO 2 DOOR / GTS 1973 – 1973 75 ft-lbs
308 – ALL 2 DOOR / COUPE 1974 – 1985 75 ft-lbs
328 GTB/S 2 DOOR / CPE/ TARGA 1986 – 1990 75 ft-lbs
348 – ALL 2 DOOR / SPIDER 1990 – 1995 75 ft-lbs
400I 2 DOOR / AUTOMATIC 1982 – 1984 75 ft-lbs
412I 2 DOOR / SEDAN 1987 – 1987 75 ft-lbs
456 -ALL 2 DOOR / 2+2 COUPE 1995 – 2004 90 ft-lbs
458 ALL / ITALIA 2010 – 2015 80 ft-lbs
512 TR 2 DOOR / COUPE 1992 – 1995 86 ft-lbs
550 COUPE / MARANELLO 1997 – 2002 100 ft-lbs
575M COUPE / MARANELLO 2003 – 2007 80 ft-lbs
599 – ALL BASE / FIORANO 2007 – 2011 80 ft-lbs
612 COUPE / SCAGLIETTI 2004 – 2011 80 ft-lbs
BB512 2 DOOR / BOXER 1983 – 1984 86 ft-lbs
CALIFORNIA 19″BASE / ALL 2010 – 2013 80 ft-lbs
CALIFORNIA T 19″BASE / ALL 2014 – 2017 80 ft-lbs
ENZO COUPE / V-12 2003 – 2004 481 ft-lbs
F12 20″BASE / BERLINETTA 2013 – 2017 80 ft-lbs
F355 – ALL 2 DOOR / BERLINETTA 1995 – 1999 86 ft-lbs
F360 ALL / MODENA 2000 – 2004 80 ft-lbs
F40 2 DOOR / COUPE 1992 – 1992 468 ft-lbs
F430 ALL / ALL 2005 – 2010 80 ft-lbs
F50 2 DOOR / CONVERTBLE 1996 – 1997 90 ft-lbs
F512M 2 DOOR / COUPE 1995 – 1996 86 ft-lbs
FF 20″BASE / ALL 2012 – 2016 80 ft-lbs
GTC4 20″BASE / LUSSO 2017 – 2017 80 ft-lbs
GTO 2 DOOR / COUPE 1985 – 1985 86 ft-lbs
LAFERRARI / RACE NUT 2014 – 2014 520 ft-lbs
MONDIAL – ALL 2 DOOR / CPE / CAB 1983 – 1993 75 ft-lbs
TESTAROSSA 2 DOOR / COUPE 1985 – 1991 75 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.