Specifications 2019 Ford Truck F 150 2WD V6-2.7L Turbo
Quick reference tables for Fluid Types and Capacities 2019 Ford Truck F 150 2WD V6-2.7L Turbo. This information is provided by Sparky Express for DIY-ers, roadside assistance providers and Ford enthusiasts in general.
Engine
| Item | Specification |
|---|---|
| Displacement | 2.7L (4V) (164 CID) |
| No. of cylinders | 6 |
| Bore/stroke | 83/83 mm (3.268/3.268 in) |
| Firing order | 1-4-2-5-3-6 |
| Spark plug | 12405 |
| Spark plug gap | 0.028–0.031 in (0.7–0.8 mm) |
| Compression ratio | 10:1 |
| Engine weight | 409 Lb (189 Kg) |
Lubricants
| Item | Specification |
|---|---|
| Motorcraft® SAE 5W-30 Premium Synthetic Blend Motor Oil (US); Motorcraft® SAE 5W-30 Super Premium Motor Oil (Canada) | XO-5W30-QSP (US); CXO-5W30-LSP12 (Canada) |
Engine Oil Capacity
| Item | Specification |
|---|---|
| Service fill including oil filter | 6.0 qt (5.68 L) |
Oil Pressure
NOTE: The following oil pressure readings are acquired using a scan tool and monitoring the EOP_PRESS PID.
| Item | Specification |
|---|---|
| Reading 1: Minimum average oil pressure @ 2,000 rpm after 15 secs with engine at normal operating temperature and transmission in Park | 21 psi (144.8 kPa) |
| Reading 2: Minimum average oil pressure @ 2,000 rpm after 15 secs with engine at normal operating temperature and transmission in Park (Oil Pressure Control Solenoid connector disconnected) | Reading 1 value plus 8 psi (55.1 kPa) |
Cylinder Head and Valve Train
| Item | Specification |
|---|---|
| Cylinder head gasket surface flatness | Flat within 0.08 mm (0.003 in) length end to end, area 150 mm (5.9 in) x 150 mm (5.9 in) (or full width) should be less than 0.05 mm (0.002 in) |
| Valve guide bore inner diameter | 0.2155–0.2167 in (5.473–5.503 mm) |
| Valve stem diameter - intake | 0.2138–0.2145 in (5.43–5.448 mm) |
| Valve stem diameter - exhaust | 0.2133–0.2140 in (5.417–5.435 mm) |
| Valve stem-to-guide clearance - intake | 0.0010–0.0029 in (.025–.073 mm) |
| Valve stem-to-guide clearance - exhaust | 0.0015–0.0034 in (.038–.086 mm) |
| Valve head diameter - intake | 1.2748–1.2843 in (32.38–32.62 mm) |
| Valve head diameter - exhaust | 1.1094–1.1189 in (28.18–28.42 mm) |
| Valve face runout | 0.0000–0.0020 in (–.05 mm) |
| Valve face angle | 45.5 — 46.0 degrees |
| Valve seat runout | 0.0000–0.0008 in (–.02 mm) |
| Valve seat angle | 44.5 — 45.5 degrees |
| Valve spring free length (approx.) | 2.0394 in (51.8 mm) |
| Valve spring compression pressure (N @ spec. length) | 553 — 607 N @ 27.0 mm |
| Valve spring installed height — Exhaust | 1.4173 in (36 mm) |
| Valve spring installed height — Intake | 1.4567 in (37 mm) |
| Valve spring installed height pressure (N @ spec. length) | 286 — 318 N @ 37 mm |
| Valve spring installed pressure — service limit | 5 % force loss @ 37 mm |
Hydraulic Lash Adjuster
| Item | Specification |
|---|---|
| Diameter — intake | 0.4720–0.4724 in (11.989–12 mm) |
| Diameter — exhaust | 0.4720–0.4724 in (11.989–12 mm) |
| Clearance-to-bore | 0.0004–0.0020 in (.01–.051 mm) |
| Collapsed lash adjuster gap | 0.0138–0.0335 in (.35–.85 mm) |
Camshaft
| Item | Specification |
|---|---|
| Theoretical valve lift (intake) @ 0 lash | 0.3937 in (10 mm) |
| Theoretical valve lift (exhaust) @ 0 lash | 0.3543 in (9 mm) |
| Lobe lift - intake | 0.2067 in (5.25 mm) |
| Lobe lift - exhaust | 0.1870 in (4.75 mm) |
| Camshaft journal bore inside diameter — 1st journal | 0.0011–0.0028 in (.027–.072 mm) |
| Camshaft journal bore inside diameter — intermediate journals | 0.0011–0.0028 in (.027–.072 mm) |
| Camshaft bearing outside diameter — 1st journal | 1.3764–1.3772 in (34.96–34.98 mm) |
| Camshaft bearing outside diameter — intermediate journals | 1.1263–1.1273 in (28.607–28.633 mm) |
| End play | 0.0010–0.0059 in (.025–.15 mm) |
Cylinder Block
| Item | Specification |
|---|---|
| Cylinder bore diameter | 3.268–3.268 in (83–83.018 mm) |
| Cylinder bore roundness | 0.0004 in (.01 mm) |
| Cylinder bore taper | 0.0005 in (.013 mm) |
| Block main bore roundness | 0.0003 in (.007 mm) |
| Main bearing bore inside diameter | 2.850–2.851 in (72.402–72.422 mm) |
| Head gasket surface flatness | Flat within 0.150 mm (0.005 in) overall 0.050 mm (0.001 in) per 150 mm (5.905 in) x 150 mm (5.905 in) 0.025 mm (0.0009 in) per 25 mm (0.98 in) x 25 mm (0.98 in) |
Crankshaft
| Item | Specification |
|---|---|
| Main bearing journal diameter | 2.6568–2.6576 in (67.483–67.503 mm) |
| Main bearing journal-to-main bearing clearance | 0.0020–0.0024 in (.05–.062 mm) |
| Connecting rod journal diameter | 2.2037–2.2044 in (55.973–55.993 mm) |
| Crankshaft end play | 0.0020–0.0115 in (.051–.291 mm) |
Piston and Connecting Rod
| Item | Specification |
|---|---|
| Piston diameter - single grade | 3.2648–3.2654 in (82.926–82.94 mm) |
| Piston-to-cylinder bore clearance | 0.0024–0.0036 in (.06–.092 mm) |
| Piston ring end gap - compression (top, gauge diameter) | 0.0110–0.0130 in (.28–.33 mm) |
| Piston ring end gap - compression (bottom, gauge diameter) | 0.0157–0.0276 in (.4–.7 mm) |
| Piston ring end gap — oil ring (steel rail, gauge diameter) | 0.0059–0.0177 in (.15–.45 mm) |
| Piston ring groove width - compression (top) | 0.0484–0.0492 in (1.23–1.25 mm) |
| Piston ring groove width — compression (bottom) | 0.0406–0.0413 in (1.03–1.05 mm) |
| Piston ring groove width - oil ring | 0.0799–0.0807 in (2.03–2.05 mm) |
| Piston ring width - upper compression ring | 0.0461–0.0469 in (1.17–1.19 mm) |
| Piston ring width - lower compression ring | 0.0382–0.0390 in (.97–.99 mm) |
| Piston ring-to-groove clearance (upper and lower compression rings) | 0.0016–0.0031 in (.04–.08 mm) |
| Piston pin bore diameter | 0.8663–0.8665 in (22.004–22.008 mm) |
| Piston pin diameter | 0.8659–0.8661 in (21.995–22 mm) |
| Piston pin length | 1.9646–1.9764 in (49.9–50.2 mm) |
| Piston pin-to-piston fit | 0.0002–0.0005 in (.004–.013 mm) |
| Piston-to-connecting rod clearance | 0.1772 in (4.5 mm) |
| Connecting rod-to-pin clearance - standard | 0.0006–0.0012 in (.015–.03 mm) |
| Connecting rod pin bore diameter | 0.8667–0.8671 in (22.015–22.025 mm) |
| Connecting rod length (center-to-center) | 5.7465–5.7496 in (145.96–146.04 mm) |
| Connecting rod maximum allowed bend | 0.0008 in (.02 mm) |
| Connecting rod maximum allowed twist | 0.0016 in (.04 mm) |
| Connecting rod bearing bore diameter | 2.3397–2.3402 in (59.428–59.442 mm) |
| Connecting rod bearing-to-crankshaft clearance | 0.0017–0.0035 in (.042–.088 mm) |
| Connecting rod side clearance (assembled to crank) - standard | 0.0049–0.0148 in (.125–.375 mm) |
| Connecting rod side clearance (assembled to crank) - service limit | 0.0049–0.0148 in (.125–.375 mm) |