Honda Wheel Lug Nut Torque Chart


Honda Wheel Lug Nut Torque Specs, All Models.

If you are planning on installing a wheel on your Honda, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Honda Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Honda vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Honda Wheel Lug Nut Torque Specs Recommendations

Make Model Trim Year Range Torque

HONDA

ACCORD - ALL ALL / ALL 1982 - 2018 80 ft-lbs
CIVIC - ALL ALL / LX 1984 - 2016 80 ft-lbs
CROSSTOUR 17"BASE / EX 2010 - 2015 80 ft-lbs
CR-V ALL / ALL 1997 - 2016 80 ft-lbs
CRX ALL / HF 1984 - 1991 80 ft-lbs
CR-Z 16"BASE / ALL 2011 - 2016 80 ft-lbs
DEL SOL ALL / S 1993 - 1997 80 ft-lbs
ELEMENT 2WD / DX/EX 2003 - 2011 80 ft-lbs
EV PLUS ALL / HATCHBACK 1997 - 1999 80 ft-lbs
FIT 14-INCH / BASE 2007 - 2018 80 ft-lbs
HR-V 17"BASE / LX/EX/EX-L 2016 - 2018 80 ft-lbs
INSIGHT ALL / ALL 2000 - 2014 80 ft-lbs
ODYSSEY ALL / LX/EX 1995 - 2004 80 ft-lbs
ODYSSEY PAX / TOURING 2005 - 2019 95 ft-lbs
PASSPORT 2WD / P215/75R15 1994 - 2002 90 ft-lbs
PILOT LX/EX / SUV 2003 - 2008 80 ft-lbs
PILOT 17"BASE / LX/EX/EX-L 2009 - 2015 90 ft-lbs
PILOT 18"BASE / LX/EX/EX-L 2016 - 2016 95 ft-lbs
PRELUDE ALL / BASE/SI 1985 - 2001 80 ft-lbs
RIDGELINE ALL / RTS/RTL 2006 - 2019 95 ft-lbs
S2000 2 DOOR / CONVERTBLE 2000 - 2009 80 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.