Mitsubishi Wheel Lug Nut Torque Chart, Mitsubishi, Specs, Wheel Torque, Wiki, Sparky Express.

Mitsubishi Lug Nut Torque Specs

Mitsubishi Lug Nut Torque Specs, All Models

If you are planning on installing a wheel on your Mitsubishi, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Mitsubishi Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Mitsubishi vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Mitsubishi Lug Nut Torque Specs Recommendations

Make Model Trim Year Range Torque

MITSUBISHI

3000GT ALL / VR4 COUPE 1991 - 1999 100 ft-lbs
CORDIA ALL / L/LS 1985 - 1988 80 ft-lbs
DIAMANTE ALL / SEDAN 1992 - 2004 80 ft-lbs
ECLIPSE ALL / BASE 1990 - 1999 100 ft-lbs
ECLIPSE ALL / GS 2000 - 2012 80 ft-lbs
ECLIPSE SPYDER 17-INCH / GS/GT 2007 - 2012 80 ft-lbs
ENDEAVOR 17-INCH / ALL 2004 - 2011 80 ft-lbs
EXPO ALL / ALL 1992 - 1995 80 ft-lbs
GALANT 14" BASE / ALL 1985 - 2012 80 ft-lbs
I-MIEV 15"BASE / ES 2018 - 2018 Refer to owner's manual ft-lbs
I-MIEV 15"BASE / ES/SE 2012 - 2016 80 ft-lbs
LANCER SEDAN / ES 2002 - 2018 80 ft-lbs
LANCER SPORTBCK 18"BASE / GTS 2010 - 2014 80 ft-lbs
MIRAGE 14"BASE / ES 2018 - 2018 Refer to owner's manual ft-lbs
MIRAGE ALL / BASE/L/M 1985 - 2018 80 ft-lbs
MONTERO ALL / ALL 1985 - 2006 85 ft-lbs
MONTERO 15" BASE / LS/RS/SR 1995 - 1999 90 ft-lbs
MONTERO SPORT 15" BASE / ES 2001 - 2004 85 ft-lbs
OUTLANDER 2WD / LS/XLS 2003 - 2016 80 ft-lbs
OUTLANDER SPORT 16"BASE / ES 2011 - 2016 80 ft-lbs
PICK-UP ALL / 4WD 1988 - 1995 100 ft-lbs
PRECIS ALL / BASE/LS/RS 1987 - 1994 70 ft-lbs
RAIDER ALL CABS / 265/70R16 2006 - 2009 135 ft-lbs
SIGMA ALL / V6 1989 - 1990 80 ft-lbs
STARION 2/DOOR / ES 1983 - 1989 80 ft-lbs
TREDIA ALL / ALL 1984 - 1988 80 ft-lbs
VAN/WAGON ALL / ALL 1987 - 1990 100 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.