Nissan Wheel Lug Nut Torque Chart


Nissan Wheel Lug Nut Torque Specs, All Models.

If you are planning on installing a wheel on your Nissan, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Nissan Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Nissan vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Nissan Wheel Lug Nut Torque Specs Recommendations

Make Model Trim Year Range Torque

NISSAN

200SX 14"BASE / ALL 1983 - 1998 85 ft-lbs
240SX 15" BASE / ALL 1989 - 1998 85 ft-lbs
240Z ALL / ALL 1971 - 1973 85 ft-lbs
260Z ALL / ALL 1974 - 1975 85 ft-lbs
280Z/ZX ALL / ALL 1976 - 1983 85 ft-lbs
280ZX ALL / TURBO 1982 - 1982 85 ft-lbs
300ZX ALL / 50TH ANNIV 1984 - 1996 85 ft-lbs
350Z COUPE COUPE / BASE 2003 - 2008 85 ft-lbs
350Z ROADSTER CONVRTBL / ENTHUSIAST 2004 - 2009 85 ft-lbs
370Z COUPE 18"BASE / BASE 2009 - 2018 85 ft-lbs
370Z ROADSTER COUPE NISMO 2010 - 2018 85 ft-lbs
ALTIMA ALL / ALL 1993 - 2007 85 ft-lbs
ALTIMA COUPE 17"BASE / 3.5 SE 2008 - 2013 85 ft-lbs
ALTIMA SEDAN 16"BASE / 2.5 BASE 2008 - 2018 85 ft-lbs
ARMADA 20-INCH / SE 2008 - 2015 100 ft-lbs
ARMADA 18-INCH / SE/LE 2004 - 2007 105 ft-lbs
ARMADA 20"BASE / PLATINUM 2018 - 2018 135 ft-lbs
AXXESS ALL / ALL 1989 - 1994 85 ft-lbs
CUBE 15"BASE / 1.8 2009 - 2014 85 ft-lbs
FRONTIER S / SV / 4WD 1998 - 2012 105 ft-lbs
FRONTIER S / SV / 4WD 2012 - 2018 100 ft-lbs
GT-R ALL / ALL 2009 - 2018 100 ft-lbs
GT-R - NISMO COUPE 2009 - 2018 115 ft-lbs
JUKE 18"BASE / NISMO RS 2015 - 2016 80 ft-lbs
JUKE 17"BASE / S 2011 - 2016 85 ft-lbs
LEAF ALL / ALL 2011 - 2016 85 ft-lbs
MAXIMA SEDAN / ALL 1983 - 2018 85 ft-lbs
MAXIMA SEDAN / 3.5 SL/SE 2004 - 2004 90 ft-lbs
MURANO SUV / S/SL/SE 2003 - 2016 80 ft-lbs
NV 1500 17"BASE / CARGO 2012 - 2015 140 ft-lbs
NV 200 15"BASE / CARGO 2013 - 2015 85 ft-lbs
NV 2500 17"BASE / CARGO 2012 - 2018 140 ft-lbs
NV 3500 17"BASE / CARGO 2012 - 2018 140 ft-lbs
NV200 15"BASE / CARGO 2013 - 2013 95 ft-lbs
NX1600 ALL / COUPE 1991 - 1993 85 ft-lbs
NX2000 14" BASE / COUPE 1991 - 1993 85 ft-lbs
PATHFINDER 2WD / E/XE 1987 - 2012 105 ft-lbs
PATHFINDER 18"BASE / S 2013 - 2018 85 ft-lbs
PICK-UP 14" BASE / 2WD/ALL 1987 - 1997 105 ft-lbs
PULSAR ALL / ALL 1983 - 1990 85 ft-lbs
QUEST 15" BASE / ALL 1993 - 2015 85 ft-lbs
ROGUE 17"BASE / SL 2008 - 2016 85 ft-lbs
ROGUE SELECT 16"BASE / S 2014 - 2015 85 ft-lbs
SENTRA SEDAN / SE 1987 - 1994 75 ft-lbs
SENTRA SEDAN / BASE/XE 1995 - 2018 85 ft-lbs
SENTRA SEDAN / XE/E/GXE 1982 - 2003 90 ft-lbs
STANZA ALL / ALL 1982 - 1992 85 ft-lbs
TITAN BASE / SE/LE ALL 2005 - 2015 100 ft-lbs
TITAN BASE / SE/LE ALL 2004 - 2008 105 ft-lbs
TITAN XD 18'BASE / PRO-4X 2016 - 2018 135 ft-lbs
VERSA 15-INCH / ALL 2007 - 2011 85 ft-lbs
VERSA HATCHBACK 15"BASE / S 2012 - 2013 85 ft-lbs
VERSA NOTE 15"BASE / S 2014 - 2018 85 ft-lbs
VERSA SEDAN 15"BASE / ALL 2012 - 2018 85 ft-lbs
XTERRA 15" BASE / ALL 2000 - 2015 100 ft-lbs
XTERRA 4WD / OFF ROAD 2005 - 2007 80 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.