Toyota Wheel Lug Nut Torque Chart


Toyota Lug Nut Torque Specs, All Models.

If you are planning on installing a wheel on your Toyota, it is important to be aware of the manufacturer's recommended torque settings. Using the proper torque helps ensure that the wheel assembly is securely installed. The Toyota Wheel Lug Nut Torque Chart we have compiled can be used as a quick reference guide by roadside assistance providers or DIY enthusiasts when working on any Toyota vehicle.

Using the manufacturer's recommended torque also helps guarantee that there isn’t either too much or too little pressure on any of the assemblies to which the wheel attaches. Before you install your wheels, check your vehicle’s recommended torque.

Toyota Wheel Lug Nut Torque Specs Recommendations

Make Model Trim Year Range Torque

TOYOTA

4 RUNNER ALL 1985 - 1997 80 ft-lbs
4 RUNNER ALL 1996 - 2021 85 ft-lbs
AVALON 4 DOOR / XL/XLS 1995 - 2021 80 ft-lbs
CAMRY 2/4 DOOR / ALL 1984 - 2021 80 ft-lbs
CELICA 2/DOOR / ST/GT 1985 - 2005 80 ft-lbs
C-HR CUV 2018 - 2021 80 ft-lbs
COROLLA ALL / ALL/4-100 1985 - 2018 80 ft-lbs
COROLLA IM 17"BASE / 5-D00R 2018 - 2018 80 ft-lbs
COROLLA ALL 2019 - 2021 80 ft-lbs
CRESSIDA BASE / WAGON 1985 - 1992 80 ft-lbs
ECHO ALL / ALL 2000 - 2005 80 ft-lbs
FJ CRUISER 17-INCH / 4WD 2007 - 2014 85 ft-lbs
HIGHLANDER 16-INCH / BASE 2001 - 2016 80 ft-lbs
LANDCRUISER 4/DOOR / ALL 1998 - 2018 97 ft-lbs
LANDCRUISER OPT 1 / SUV 1985 - 1993 116 ft-lbs
LANDCRUISER ALL / ALL 1994 - 1997 108 ft-lbs
MATRIX 16-INCH / XR 2003 - 2013 80 ft-lbs
MIRAI 17" BASE / FUEL CELL 2016 - 2016 80 ft-lbs
MR2 ALL / ALL 1985 - 2005 80 ft-lbs
PASEO 2/DOOR / ALL 1992 - 1998 80 ft-lbs
PICK-UP BASE / 4WD 1986 - 1994 80 ft-lbs
PREVIA DLX / ALL-TRAC 1992 - 1997 80 ft-lbs
PRIUS ALL / SEDAN 1999 - 2018 80 ft-lbs
PRIUS C 15"BASE / 5-DOOR 2012 - 2016 80 ft-lbs
PRIUS V 16"BASE / ALL 2012 - 2018 80 ft-lbs
RAV4 16"BASE / 2WD 1996 - 2018 80 ft-lbs
SEQUOIA 18"BASE / SR5 2008 - 2018 100 ft-lbs
SEQUOIA BASE / SR5 2001 - 2007 85 ft-lbs
SIENNA VAN / CE/LE 1998 - 2018 80 ft-lbs
SOLARA 15" BASE / SLE 1999 - 2007 80 ft-lbs
SOLARA CONVTBLE 16"BASE / SE 2008 - 2008 80 ft-lbs
SOLARA COUPE 16"BASE / SLE 4-CYL. 2008 - 2008 80 ft-lbs
SUPRA 3/DOOR / LIFTBACK 1985 - 1998 80 ft-lbs
T-100 15"BASE / 2WD 1993 - 1998 80 ft-lbs
TACOMA 15"BASE / 4WD 1995 - 2018 85 ft-lbs
TERCEL 2/DOOR / ALL 1985 - 1998 80 ft-lbs
TUNDRA ALL CABS / 275/65R18 2007 - 2018 100 ft-lbs
TUNDRA STL.WHLS / 255/70R18 2007 - 2018 150 ft-lbs
TUNDRA 2WD / REG CAB 2003 - 2006 85 ft-lbs
TUNDRA BASE / BASE 2000 - 2004 90 ft-lbs
VAN WAGON 3/DOOR / RWD 1985 - 1990 80 ft-lbs
VENZA 20"BASE / 6-CYL 2009 - 2015 80 ft-lbs
YARIS 3-DOOR 15"BASE / L/LE 2014 - 2016 80 ft-lbs
YARIS 5-DOOR 15"BASE / L/LE 2014 - 2016 80 ft-lbs
YARIS 15-INCH / SDN/LFTBCK 2007 - 2013 80 ft-lbs
YARIS IA 16"BASE / SEDAN 2018 - 2018 80 ft-lbs

Remove or Install Front or Rear Wheel - Generic Instructions

When removing and installing a wheel on your vehicle, always follow these generic instructions, but for more information please refer to your owner's manual. When lifting your vehicle, make sure you use the proper equipment and that you only lift the vehicle from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on with two wheel chokes on both side of the wheel to prevent the car from rolling and fall of the jack while you're working on it. Never get under the vehicle when it is resting only on the jack.

  • Always release the wheel lockable nuts or bolts by hand (use a breaker bar) and NOT by using an impact drill. Do not jump or use your foot on the breaker bar.
  • Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.
  • Check brake disc retaining bolt for tight fit.
  • Apply anti-seize paste on the wheel centring in the wheel rim.
  • Clean wheel bolts or nuts and check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! Do not apply oil or grease to wheel studs or bolts.
  • The wheel rim must rest uniformly against the brake disc.
  • Screw in the wheel bolts or lug nuts and evenly tighten by hand in a crosswise sequence in order to centre the wheel rim.
  • Tighten the wheel bolts or lug nuts to the specified tightening toque in a crosswise sequence using a calibrated torque wrench.
  • Check all wheel bolts or lug nuts in the same sequence and retighten to the prescribed tightening torque if necessary.
  • Under no circumstances use pneumatic or electric screwdrivers to screw in and tighten the wheel bolts.